Conceptualizing flexible papers using cellulose model surfaces and polymer particles.

Cellulose, as a naturally abundant and biocompatible material, is still gaining interest due to its high potential for functionalization. This makes cellulose a promising candidate for replacing plastics. Understanding how cellulose interacts with various additives is crucial for creating composite materials with diverse properties, as it is the case for plastics. In addition, the mechanical properties of the composite materials are assumed to be related to the mobility of the additives against the cellulose. Using a well-defined cellulose model surface (CMS), we aim to understand the adsorption and desorption of two polymeric particles (core-shell particles and microgels) to/from the cellulose surface. The nanomechanics of particles and CMS are quantified by indentation measurements with an atomic force microscope (AFM). AFM topography measurements quantified particle adsorption and desorption on the CMS, while peak force AFM measurements determined the force needed to move individual particles. Both particles and the CMS exhibited pH-dependent charge behavior, allowing a tunable interaction between them. Particle adsorption was irreversible and driven by electrostatic forces. In contrast, desorption and particle mobility forces are dominated by structural morphology. In addition, we found that an annealing procedure consisting of swelling/drying cycles significantly increased the adhesion strength of both particles. Using the data, we achieve a deeper understanding of the interaction of cellulose with polymeric particles, with the potential to advance the development of functional materials and contribute to various fields, including smart packaging, sensors, and biomedical applications.

The cyto-linker and scaffolding protein "plectin" mis-localization leads to softening of cancer cells.

Discovering tools to prevent cancer progression requires understanding the fundamental differences between normal and cancer cells. More than a decade ago, atomic force microscopy (AFM) revealed cancer cells' softer body compared to their healthy counterparts. Here, we investigated the mechanism underlying the softening of cancerous cells in comparison with their healthy counterparts based on AFM high resolution stiffness tomography and 3D confocal microscopy. We showed microtubules (MTs) network in invasive ductal carcinoma cell cytoskeleton is basally located and segmented for around 400 nm from the cell periphery. Additionally, the cytoskeleton scaffolding protein plectin exhibits a mis-localization from the cytoplasm to the surface of cells in the carcinoma which justifies the dissociation of the MT network from the cell's cortex. Furthermore, the assessment of MTs' persistence length using a worm-like-chain (WLC) model in high resolution AFM images showed lower persistence length of the single MTs in ductal carcinoma compared to that in the normal state. Overall, these tuned mechanics support the invasive cells to ascertain more flexibility under compressive forces in small deformations. These data provide new insights into the structural origins of cancer aids in progression.

Self-Assembly of Polymer-Modified FePt Magnetic Nanoparticles and Block Copolymers.

The fabrication of nanocomposites containing magnetic nanoparticles is gaining interest as a model for application in small electronic devices. The self-assembly of block copolymers (BCPs) makes these materials ideal for use as a soft matrix to support the structural ordering of the nanoparticles. In this work, a high-molecular-weight polystyrene-b-poly(methyl methacrylate) block copolymer (PS-b-PMMA) was synthesized through anionic polymerization. The influence of the addition of different ratios of PMMA-coated FePt nanoparticles (NPs) on the self-assembled morphology was investigated using transmission electron microscopy (TEM) and small-angle X-ray scattering (SAXS). The self-assembly of the NPs inside the PMMA phase at low particle concentrations was analyzed statistically, and the negative effect of higher particle ratios on the lamellar BCP morphology became visible. The placement of the NPs inside the PMMA phase was also compared to theoretical descriptions. The magnetic addressability of the FePt nanoparticles inside the nanocomposite films was finally analyzed using bimodal magnetic force microscopy and proved the magnetic nature of the nanoparticles inside the microphase-separated BCP films.

Concentration gradients in evaporating binary droplets probed by spatially resolved Raman and NMR spectroscopy.

Understanding the evaporation process of binary sessile droplets is essential for optimizing various technical processes, such as inkjet printing or heat transfer. Liquid mixtures whose evaporation and wetting properties may differ significantly from those of pure liquids are particularly interesting. Concentration gradients may occur in these binary droplets. The challenge is to measure concentration gradients without affecting the evaporation process. Here, spectroscopic methods with spatial resolution can discriminate between the components of a liquid mixture. We show that confocal Raman microscopy and spatially resolved NMR spectroscopy can be used as complementary methods to measure concentration gradients in evaporating 1-butanol/1-hexanol droplets on a hydrophobic surface. Deuterating one of the liquids allows analysis of the local composition through the comparison of the intensities of the C­H and C­D stretching bands in Raman spectra. Thus, a concentration gradient in the evaporating droplet was established. Spatially resolved NMR spectroscopy revealed the composition at different positions of a droplet evaporating in the NMR tube, an environment in which air exchange is less pronounced. While not being perfectly comparable, both methods­confocal Raman and spatially resolved NMR experiments­show the presence of a vertical concentration gradient as 1-butanol/1-hexanol droplets evaporate.

Investigation and comparison of resin materials in transparent DLP-printing for application in cell culture and organs-on-a-chip.

Organs-on-a-Chip (OOCs) have recently led to major discoveries and a better understanding of 3D cell organization, cell-cell interactions and tissue response to drugs and biological cues. However, their complexity and variability are still limited by the available fabrication technology. Transparent, cytocompatible and high-resolution 3D-printing could overcome these limitations, offering a flexible and low-cost alternative to soft lithography. Many advances have been made in stereolithography printing regarding resin formulation and the general printing process, but a systematic analysis of the printing process steps, employed resins and post-treatment procedures with a strong focus on the requirements in OOCs is missing. To fill this gap, this work provides an in-depth analysis of three different resin systems in comparison to polystyrene (PS) and poly(dimethylsiloxane) (PDMS), which can be considered the gold-standards in cell culture and microfluidics. The resins were characterized with respect to transparency, cytocompatibility and print resolution. These properties are not only governed by the resin composition, but additionally by the post-treatment procedure. The investigation of the mechanical (elastic modulus ∼2.2 GPa) and wetting properties (∼60° native / 20° plasma treated) showed a behavior very similar to PS. In addition, the absorbance of small molecules was two orders of magnitude lower in the applied resins (diffusion constant ∼0.01 µm2 s-1) than for PDMS (2.5 µm2 s-1), demonstrating the intrinsic suitability of these materials for OOCs. Raman spectroscopy and UV/VIS spectrophotometry revealed that post-treatment increased monomer conversion up to 2 times and removed photo initiator residues, leading to an increased transparency of up to 50% and up to 10-times higher cell viability. High magnification fluorescence imaging of HUVECs and L929 cells cultivated on printed dishes shows the high optical qualities of prints fabricated by the Digital Light Processing (DLP) printer. Finally, components of microfluidic chips such as high-aspect ratio pillars and holes with a diameter of 50 µm were printed. Concluding, the suitability of DLP-printing for OOCs was demonstrated by filling a printed chip with a cell-hydrogel mixture using a microvalve bioprinter, followed by the successful cultivation under perfusion. Our results highlight that DLP-printing has matured into a robust fabrication technology ready for application in extensive and versatile OOC research.

Systematic study of precursor effects on structure and oxygen reduction reaction activity of FeNC catalysts.

In this work, the effect of porphyrin loading and template size is varied systematically to study its impact on the oxygen reduction reaction (ORR) activity and selectivity as followed by rotating ring disc electrode experiments in both acidic and alkaline electrolytes. The structural composition and morphology are investigated by 57Fe Mössbauer spectroscopy, transmission electron microscopy, Raman spectroscopy and Brunauer-Emmett-Teller analysis. It is shown that with decreasing template size, specifically the ORR performance towards fuel cell application gets improved, while at constant area loading of the iron precursor (here expressed in number of porphyrin layers), the iron signature does not change much. Moreover, it is well illustrated that too large area loadings result in the formation of undesired side phases that also cause a decrease in the performance, specifically in acidic electrolyte. Thus, if the impact of morphology is the focus of research it is important to consider the area loading rather than its weight loading. At constant weight loading, beside morphology the structural composition can also change and impact the catalytic performance. This article is part of the theme issue 'Bio-derived and bioinspired sustainable advanced materials for emerging technologies (part 2)'.

Endothelialization of PDMS-based microfluidic devices under high shear stress conditions.

Microfluidic systems made out of polydimethylsiloxane (PDMS) offer a platform to mimic vascular flow conditions in model systems at well-defined shear stresses. However, extracellular matrix (ECM) proteins that are physisorbed on the PDMS are not reliably attached under high shear stress conditions, which makes long-term experiments difficult. To overcome this limitation, we functionalized PDMS surfaces with 3-aminopropyltriethoxysilane (APTES) by using different surface activation methods to develop a stable linkage between the PDMS surface and collagen, which served as a model ECM protein. The stability of the protein coating inside the microfluidic devices was evaluated in perfusion experiments with phosphate-buffered saline (PBS) at 10-40 dynes/cm2 wall shear stress. To assess the stability of cell adhesion, endothelial cells were grown in a multi-shear device over a shear stress range of 20-150 dynes/cm2. Cells on the APTES-mediated collagen coating were stable over the entire shear stress range in PBS (pH 9) for 48 h. The results suggest that at high pH values, the electrostatic interaction between APTES-coated surfaces and collagen molecules offer a very promising tool to modify PDMS-based microfluidic devices for long-term endothelialization under high shear stress conditions.

Immobilisation of CXCL8 gradients in microfluidic devices for migration experiments.

The release of inflammatory chemokines leads to the formation of chemokine gradients that result in the directed migration of immune cells to the site of injury. In this process, cells respond to soluble gradients (chemotaxis) as well as to immobilised gradients (haptotaxis). Surface-bound chemokine gradients are mostly presented by endothelial cells and supported by glycosaminoglycans (GAGs), such as heparan sulfate, involving the GAG binding site of chemokines. Microfluidic devices have been used to analyse cell migration along soluble chemokine gradients, as these devices allow the generation of stable gradients with resolutions in the range of microns. To immobilise well-controlled soluble gradients of interleukin-8 (CXCL8), an inflammatory chemokine, we developed a simple procedure using a heparin-coated PDMS-microfluidic device. We used these immobilised gradients for migration experiments with CXCL8-responsive THP-1 cells and confirmed directed cell migration. This setup might be useful for the examination of factors that may alter chemotaxis and haptotaxis as well as synergistic and antagonistic effects of other soluble and immobilised chemokines.

Probing Charge Accumulation at SrMnO3/SrTiO3 Heterointerfaces via Advanced Electron Microscopy and Spectroscopy.

The last three decades have seen a growing trend toward studying the interfacial phenomena in complex oxide heterostructures. Of particular concern is the charge distribution at interfaces, which is a crucial factor in controlling the interface transport behavior. However, the study of the charge distribution is very challenging due to its small length scale and the intricate structure and chemistry at interfaces. Furthermore, the underlying origin of the interfacial charge distribution has been rarely studied in-depth and is still poorly understood. Here, by a combination of aberration-corrected scanning transmission electron microscopy (STEM) and spectroscopy techniques, we identify the charge accumulation in the SrMnO3 (SMO) side of SrMnO3/SrTiO3 heterointerfaces and find that the charge density attains the maximum of 0.13 ± 0.07 e-/unit cell (uc) at the first SMO monolayer. Based on quantitative atomic-scale STEM analyses and first-principle calculations, we explore the origin of interfacial charge accumulation in terms of epitaxial strain-favored oxygen vacancies, cationic interdiffusion, interfacial charge transfer, and space-charge effects. This study, therefore, provides a comprehensive description of the charge distribution and related mechanisms at the SMO/STO heterointerfaces, which is beneficial for the functionality manipulation via charge engineering at interfaces.

Direct Observation of Huge Flexoelectric Polarization around Crack Tips.

Flexoelectricity is especially relevant for nanoscale structures, and it is expected to be largest at the tip of cracks. We demonstrate the presence of a huge flexoelectric polarization at crack tips in SrTiO3 by direct observation with scanning transmission electron microscopy. We observe an averaged polarization of 62 ± 16 µC cm-2 in the three unit cells adjacent to the crack tip, which is one of the largest flexoelectric polarizations ever reported. The polarization is screened by an electron density of 0.7 ± 0.1 e-/uc localized within one unit cell. These findings reveal the relevance of flexoelectricity for the science of crack formation and propagation.

Insights into the interplay of wetting and transport in mesoporous silica films.

The understanding and design of wetting-transport and wetting-charge-transport interplay in nanometer-sized pores is a still not fully understood key step in improving nanopore transport-related applications. A control of mesopore wettability accompanied by pore filling and ionic mesopore accessibility analysis is expected to deliver major insights into this interplay of nanoscale pore wetting and transport. For a systematic understanding, we demonstrate a gradual adjustment of nanopore ionic accessibility by gradually tuning silica nanopore wettability using chemical vapor phase deposition of 1H,1H,2H,2H-perfluorooctyl dimethylchlorosilane. The mutual influence of wetting on liquid imbibition, condensation, and molecular transport as well as on heat transfer were studied by ellipsometry, cyclic voltammetry and boiling experiments, respectively. A multi-methodical analytic approach was used to directly couple wetting properties of mesoporous silica thin films to ionic mesopore accessibility allowing us to determine two different ion transport mechanisms based on three defined wetting regimes as well as a threshold hydrophobicity suppressing pore accessibility. Furthermore, boiling experiments showed a clear increase in nucleation site density upon changing the wettability of the mesoporous surfaces from hydrophilic to hydrophobic. Hence, these results provide insights into the complex interplay of pore wall functionalization, wetting, and charge-dependent nanopore properties.

Structural Properties and Magnetic Ordering in 2D Polymer Nanocomposites: Existence of Long Magnetic Dipolar Chains in Zero Field.

The existence of magnetic dipolar nanoparticle chains at zero field has been predicted theoretically for decades, but these structures are rarely observed experimentally. A prerequisite is a permanent magnetic moment on the particles forming the chain. Here we report on the observation of magnetic dipolar chains of spherical iron oxide nanoparticles with a diameter of 12.8 nm. The nanoparticles are embedded in an ultrathin polymer film. Due to the high viscosity of the polymer matrix, the dominating aggregation mechanism is driven by dipolar interactions. Smaller iron oxide nanoparticles (8 nm) show no permanent magnetic moment and do not form chains but compact aggregates. Mixed monolayers of iron oxide nanoparticles and polymer at the air-water interface are characterized by Langmuir isotherms and in situ X-ray reflectometry (XRR). The combination of the particles with a polymer leads to a stable polymer nanocomposite film at the air-water interface. XRR experiments show that nanoparticles are immersed in a thin polymer matrix of 2 nm. Using atomic force microscopy (AFM) on Langmuir-Blodgett films, we measure the lateral distribution of particles in the film. An analysis of single structures within transferred films results in fractal dimensions that are in excellent agreement with 2D simulations.

Atomic force microscopy measurements probing the mechanical properties of single collagen fibrils under the influence of UV light in situ.

Collagen plays a decisive role as a functional substrate in tissue engineering. In particular, the rigidity of the collagen influences the behaviour of the attached cells. Thus, modification and controlled adjustment of collagen's characteristics are essential. To this end, controlled exposure to ultraviolet (UV) light is a promising process because it can be temporally and spatially well defined. In this study, we investigated the effect of UV exposure on surface supported single collagen fibrils in situ. This procedure allowed for a direct comparison between the untreated and modified states of type I collagen. Atomic force microscopy was used to map the mechanical properties. Exposure to UV light was used to influence the mechanical properties of the fibrils in varied liquid environments (deionized water and phosphate-buffered saline (PBS)). The results led to the assumption that combined UV/thermal treatment in deionized water continuously lowers the elastic modulus. In contrast, experiments performed in PBS-based solutions in combination with UV-B and UV-C light or thermal treatment up to 45 °C suggested an increase in the modulus within the first 30-40 min that subsequently decreased again. Thus, the wavelength, exposure, temperature, and chemical environment are relevant parameters that need to be controlled when modifying collagen using UV light.

The Iceman's Last Meal Consisted of Fat, Wild Meat, and Cereals.

The history of humankind is marked by the constant adoption of new dietary habits affecting human physiology, metabolism, and even the development of nutrition-related disorders. Despite clear archaeological evidence for the shift from hunter-gatherer lifestyle to agriculture in Neolithic Europe [1], very little information exists on the daily dietary habits of our ancestors. By undertaking a complementary -omics approach combined with microscopy, we analyzed the stomach content of the Iceman, a 5,300-year-old European glacier mummy [2, 3]. He seems to have had a remarkably high proportion of fat in his diet, supplemented with fresh or dried wild meat, cereals, and traces of toxic bracken. Our multipronged approach provides unprecedented analytical depth, deciphering the nutritional habit, meal composition, and food-processing methods of this Copper Age individual.

Exploring Active Sites in Multi-Heteroatom-Doped Co-Based Catalysts for Hydrogen Evolution Reactions.

Today, metal-N- as well as metal-S-doped carbon materials are known to catalyze the hydrogen evolution reaction (HER). However, especially N- and S-co-doped catalysts reach highest activity, but it remains unclear if the activity is related to MNx or MSy (M=metal) sites. In this work we apply a simple method for multi-heteroatom doping and investigate the effect of cobalt content on the HER in acidic medium. The CoNx and CoSy sites were evidenced on the basis of structural characterization by Raman, X-ray induced photoelectron spectroscopy, and TEM. The presence of sulfur enables the formation of a larger number of CoNx sites. Structure-performance relationship proves that the HER activity is dominated by CoNx rather than CoSy sites. The most active catalysts also exhibit an excellent stability under galvanostatic conditions making them of interest for electrolyser application.

Improved cell adhesion under shear stress in PDMS microfluidic devices.

Microfluidic systems based on polydimethylsiloxane (PDMS) provide a versatile platform to study the mechanoresponse of cells in vitro. Under a shear flow, however, the stability of cells that were grown on physically adsorbed proteins is short lived, which limits long-term cell studies. To address this issue, we used (3-Aminopropyl)triethoxysilane (APTES) as a linker between PDMS and collagen. In micro-channels that were modified with APTES-anchored collagen, fibroblast cells demonstrated higher stability and better proliferation as compared to collagen that was physically adsorbed onto PDMS after oxygen plasma treatment. To assess the stability of the cellular adhesion, cells were forced in a shear flow until detachment. In devices with APTES-anchored collagen, cells showed better adhesion and proliferation at shear stresses between 11.6 and 93dyn/cm2 as compared to devices with the adsorbed collagen coating where the first cellular detachment occurred already at a shear stress of 23dyn/cm2. The APTES-attached collagen coating also contributed to an improved long-term cellular growth (observed for 48h) at different shear stress levels (10-300dyn/cm2). Attachment of collagen with the help of APTES thus is a very promising technique not only to modify the glass but also to modify the PDMS surfaces of microfluidic devices for mechanotransduction experiments.

Revealing the core-shell interactions of a giant strain relaxor ferroelectric 0.75Bi1/2Na1/2TiO3-0.25SrTiO3.

Lead-free relaxor ferroelectrics that feature a core-shell microstructure provide an excellent electromechanical response. They even have the potential to replace the environmentally hazardous lead-zirconia-titanate (PZT) in large strain actuation applications. Although the dielectric properties of core-shell ceramics have been extensively investigated, their piezoelectric properties are not yet well understood. To unravel the interfacial core-shell interaction, we studied the relaxation behaviour of field-induced ferroelectric domains in 0.75Bi1/2Na1/2TiO3-0.25SrTiO3 (BNT-25ST), as a typical core-shell bulk material, using a piezoresponse force microscope. We found that after poling, lateral domains emerged at the core-shell interface and propagated to the shell region. Phase field simulations showed that the increased electrical potential beneath the core is responsible for the in-plane domain evolution. Our results imply that the field-induced domains act as pivotal points at the coherent heterophase core-shell interface, reinforcing the phase transition in the non-polar shell and thus promoting the giant strain.

Visualization of polar nanoregions in lead-free relaxors via piezoresponse force microscopy in torsional dual AC resonance tracking mode.

Polar nanoregions (PNRs) play a key role in the functionality of relaxor ferroelectrics; however, visualizing them in lead-free relaxor ferroelectrics with high lateral resolution is still challenging. Thus, we studied herein the local ferroelectric domain distribution of the lead-free bismuth-based (1 -x)(Bi1/2Na1/2TiO3-Bi1/2K1/2TiO3) -x(Bi1/2Mg1/2TiO3) piezoceramics which show a relaxor behavior using dual AC resonance tracking (DART) piezoresponse force microscopy (PFM). By using excitation frequencies at either side of the contact resonance peak of the torsional cantilever vibration, an enhanced contrast in the amplitude and phase images of the piezoresponse can be achieved. Additionally, this tracking technique reduces the topographical crosstalk while mapping the local electromechanical properties. The true drive amplitude, drive phase, contact resonant frequency and quality factor can be estimated from DART-PFM data obtained with vertically or torsionally vibrating cantilevers. This procedure yields a three-dimensional quantitative map of the local piezoelectric properties of the relaxor ferroelectric samples. With this approach, torsional DART allowed for the visualization of fine substructures within the monodomains, suggesting the existence of PNRs in relaxor ferroelectrics. The domain structures of the PNRs were visualized with high precision, and the local electromechanical characteristics of the lead-free relaxor ferroelectrics were quantitatively mapped.

Cross-Linking Cellulosic Fibers with Photoreactive Polymers: Visualization with Confocal Raman and Fluorescence Microscopy.

The properties of paper sheets can be tuned by adjusting the surface or bulk chemistry using functional polymers that are applied during (online) or after (offline) papermaking processes. In particular, polymers are widely used to enhance the mechanical strength of the wet state of paper sheets. However, the mechanical strength depends not only on the chemical nature of the polymeric additives but also on the distribution of the polymer on and in the lignocellulosic paper. Here, we analyze the photochemical attachment and distribution of hydrophilic polydimethylacrylamide-co-methacrylate-benzophenone P(DMAA-co-MABP) copolymers with defined amounts of photoreactive benzophenone moieties in model paper sheets. Raman microscopy was used for the unambiguous identification of P(DMAA-co-MABP) and cellulose specific bands and thus the copolymer distribution within the cellulose matrix. Two-dimensional Raman spectral maps at the intersections of overlapping cellulose fibers document that the macromolecules only partially surround the cellulose fibers, favor to attach to the fiber surface, and connect the cellulose fibers at crossings. Moreover, the copolymer appears to accumulate preferentially in holes, vacancies, and dips on the cellulose fiber surface. Correlative brightfield, Raman, and confocal laser scanning microscopy finally reveal a reticular three-dimensional distribution of the polymer and show that the polymer is predominately deposited in regions of high capillarity (i.e., in proximity to fine cellulose fibrils). These data provide deeper insights into the effects of paper functionalization with a copolymer and aid in understanding how these agents ultimately influence the local and overall properties of paper.

Bimodal frequency-modulated atomic force microscopy with small cantilevers.

Small cantilevers with ultra-high resonant frequencies (1-3 MHz) have paved the way for high-speed atomic force microscopy. However, their potential for multi-frequency atomic force microscopy is unexplored. Because small cantilevers have small spring constants but large resonant frequencies, they are well-suited for the characterisation of delicate specimens with high imaging rates. We demonstrate their imaging capabilities in a bimodal frequency modulation mode in constant excitation on semi-crystalline polypropylene. The first two flexural modes of the cantilever were simultaneously excited. The detected frequency shift of the first eigenmode was held constant for topographical feedback, whereas the second eigenmode frequency shift was used to map the local properties of the specimen. High-resolution images were acquired depicting crystalline lamellae of approximately 12 nm in width. Additionally, dynamic force curves revealed that the contrast originated from different interaction forces between the tip and the distinct polymer regions. The technique uses gentle forces during scanning and quantified the elastic moduli Eam = 300 MPa and Ecr = 600 MPa on amorphous and crystalline regions, respectively. Thus, multimode measurements with small cantilevers allow one to map material properties on the nanoscale at high resolutions and increase the force sensitivity compared with standard cantilevers.